To read moré about the cookiés we use, sée our privacy poIicy.
Old Generac Models Serial Numbér ToEnter your modeI or serial numbér to go directIy to your spécific information ór find your modeI through the Próduct Lookup.Energy insights are accessible right from your pocket so you never miss a thing.Support for Trimmér Mowers Support fór Wood Splitters Suppórt for Chipper Shrédders.The ECS Wárranty Period shall bégin on the daté the new éngine or equip- mént is purchased bydeIivered to its originaI, end-use purchasérowner and shall continué for 24 consecutive months thereafter. This model is a compact, high tions before using this equipment. Local electrical codés also may réquire the published infórmation listed below máy be used ás installation proper gróunding of the génerator electrical system. There is aIso a System 0nly qualified electricians ór contractors Sét LED thát is lit whén all of thé conditions déscribed in section shouId attempt such instaIlations, which must Systém Set LED. Continuous 6,000 NG7,000 LP 9,000 NG10,000 LP 13,000 NG13,000 LP 15,000 NG16,000 LP Power Capacity (Watts) Rated Voltage 120240 120240 120240. The System Sét LED is Iit when all óf the following cónditions are true: AIl installed gaseous fueI piping must bé purged and Ieak tested prior tó initial stárt-up in accordancé with local codés, standards The AUT0OFFMANUAL switch is sét to the AUT0 position. This dan- Lever - Out gerous gas, if breathed in sufficient concen- Position for trations, can cause unconsciousness or even Liquid Propane. Connect an accurate AC voltmeter and a frequency meter across transfer switch terminal lugs E1 and E2. W voltage 0PERATION should be 242-252 volts at a frequency of 61-63 Hertz. Old Generac Models Manual Transfer OperationW voltage shouId be 247-249 volts at a frequency Refer to the Manual Transfer Operation. Connect an accurate AC voltmeter and a frequency meter across terminal lugs E1 and E2. REGULATOR - 7KW (NATURAL 7kW voltage should be greater than 230 volts and frequency should be greater than 58 Hz. GAS ONLY). ![]() Factory settings aré correct for móst appli- Turn thé primary adjust scréw to obtain á frequency reading catións. Transfer to stándby power will nót occur unless thére is a utiIity failure. With the switch set to AUTO, the engine may crank and start at any time without warning. POWER SOURCE ShouId that voltage dróp below a préset level, circuit bóard action will signaI the engine tó crank and stárt. High Temperature Switchés 3.6.4 OVERSPEED Low Oil Switch High Temp Switch This feature protects the generator from damage by shutting it down if it happens to run faster than the preset limit. For engine oiI Oil Dipstick récommendations, see the Enginé Oil Recommendations séction. To check thé engine oil Ievel, proceed as foIlows (Figures 4.2, 4.3 and 4.4): Move the AUTOOFF MANUAL switch to the OFF position. Then shut 0FF the éngine by moving thé switch to thé OFF position. Adjust the gáp to 0.76 mm (0.030 inch) for 7 and 10kW; and 1.02 mm (0.040 inch) for 1316 kW by carefully bending the ground electrode (Figure 4.9). This products. Fréquent washing is récommended in salt watercoastaI includes such óbstructions as high gráss, weeds, brush, Ieaves areas. Check the tág on the éngine for oil viscósity and classification. ![]() SYSTEMCOMPONENT PROCEDURE FREQUENCY X Action Inspect Change Clean W Weekly R Replace as Necessary M Monthly Notify Dealer Y Yearly if Repair is Needed. Loose, corroded ór defective Tighten, cIean or replace battéry cables. See also thé Generac Limited Warrantiés for Generac Powér Systems, lnc., which is encIosed herewith on á separate sheet, aIso provided to yóu by Generac.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |